# Troubleshooting

If you're running into problems with IPFS, use this page to debug your issues and find a solution quickly.

# Check that your IPFS daemon is running

If you're getting unexpected behavior when trying to run common commands such as ipfs get <cid> returning Error: merkledag: not found, the issue is likely that your daemon isn't running. This can be remedied by running ipfs daemon, and using a different terminal to interact with the daemon.

# IPFS is running slowly

Commands like ipfs ls are going to the network to try and find data. If for some reason, that data is not findable then Go-IPFS will just keep looking for who has the data forever. Common reasons for data not being findable are that:

  • Nobody online has it.
  • There is one node that has the data, but it's behind a NAT.
  • The node that has it has not yet advertised the data in a way that your node can find it.

You can take a look at what's going on with Bitswap using ipfs bitswap stat to help you determine if you're stuck looking for data. If the data you are looking for is perpetually in the wantlist then your node may be experiencing one of the common reasons listed above.

Some functions also have flags like --stream or --progress that can help you see incremental updates. For logging behavior, there is ipfs log, where ipfs log level can help you inspect subsystems further.

You can pass a timeout flag to basically all Go-IPFS commands if you're concerned about your CLI not responding quickly enough when the data just isn't available on the network.

# File transfers

To start, make sure that IPFS is running on both machines. To verify, run ipfs id on each machine and check if the Addresses field has anything in it. If it says null, then your node is not online, and you will need to run ipfs daemon.

Now, let's call the node with the file you want to transfer node 'A' and the node you want to get the file to node 'B'. On node a, add the file to IPFS using the ipfs add command. This will print out the multihash of the content you added. Now, on node b, you can fetch the content using ipfs get <hash>.

# On A
ipfs add myfile.txt
> added QmZJ1xT1T9KYkHhgRhbv8D7mYrbemaXwYUkg7CeHdrk1Ye myfile.txt

# On B
ipfs get QmZJ1xT1T9KYkHhgRhbv8D7mYrbemaXwYUkg7CeHdrk1Ye
> Saving file(s) to QmZJ1xT1T9KYkHhgRhbv8D7mYrbemaXwYUkg7CeHdrk1Ye
> 13 B / 13 B [=====================================================] 100.00% 1s

If that worked and your node downloaded the file, then congratulations! You just used IPFS to move files across the internet! But, if that ipfs get command is hanging, with no output, read onwards.

# Checking for existing connections

The first thing to do is to double-check that both nodes are, in fact, running and online. To do this, run ipfs id on each machine. If both nodes show some addresses (like the example below), then your nodes are online.

{
    "ID": "QmTNwsFkLAed15kQEC1ZJWPfoNbBQnMFojfJKQ9sZj1dk8",
        "PublicKey": "CAASpgIwggEiMA0GCSqGSIb3DQEBAQUAA4IBDwAwggEKAoIBAQDZb6znj3LQZKP1+X81exf+vbnqNCMtHjZ5RKTCm7Fytnfe+AI1fhs9YbZdkgFkM1HLxmIOLQj2bMXPIGxUM+EnewN8tWurx4B3+lR/LWNwNYcCFL+jF2ltc6SE6BC8kMLEZd4zidOLPZ8lIRpd0x3qmsjhGefuRwrKeKlR4tQ3C76ziOms47uLdiVVkl5LyJ5+mn4rXOjNKt/oy2O4m1St7X7/yNt8qQgYsPfe/hCOywxCEIHEkqmil+vn7bu4RpAtsUzCcBDoLUIWuU3i6qfytD05hP8Clo+at+l//ctjMxylf3IQ5qyP+yfvazk+WHcsB0tWueEmiU5P2nfUUIR3AgMBAAE=",
        "Addresses": [
            "/ip4/127.0.0.1/tcp/4001/p2p/QmTNwsFkLAed15kQEC1ZJWPfoNbBQnMFojfJKQ9sZj1dk8",
        "/ip4/127.0.0.1/udp/4001/quic/p2p/QmTNwsFkLAed15kQEC1ZJWPfoNbBQnMFojfJKQ9sZj1dk8",
        "/ip4/192.168.2.131/tcp/4001/p2p/QmTNwsFkLAed15kQEC1ZJWPfoNbBQnMFojfJKQ9sZj1dk8",
        "/ip4/192.168.2.131/udp/4001/quic/p2p/QmTNwsFkLAed15kQEC1ZJWPfoNbBQnMFojfJKQ9sZj1dk8"
        ],
        "AgentVersion": "go-ipfs/0.4.11-dev/",
        "ProtocolVersion": "ipfs/0.1.0"
}

Next, check to see if the nodes have a connection to each other. You can do this by running ipfs swarm peers on one node and checking for the other node's peer ID in the output. If the two nodes are connected, and the ipfs get command is still hanging, then something unexpected is going on, and I recommend filing an issue about it. If they are not connected, then let's try and debug why. (Note: you can skip to Manually connecting node a to node b if you just want things to work. However, going through the debugging process and reporting what happened to the IPFS team on IRC is helpful to us to understand common pitfalls that people run into).

# Checking providers

When requesting content on IPFS, nodes search the DHT for 'provider records' to see who has what content. Let's manually do that on node b to make sure that node b is able to determine that node a has the data. Run ipfs dht findprovs <hash>. We expect to see the peer ID of node a printed out. If this command returns nothing (or returns IDs that are not node a), then no record of A having the data exists on the network. This can happen if the data is added while node a does not have a daemon running. If this happens, you can run ipfs dht provide <hash> on node a to announce to the network that you have that hash. Then if you restart the ipfs get command, node b should now be able to tell that node a has the content it wants. If node a's peer ID showed up in the initial findprovs call or manually providing the hash didn't resolve the problem, then it's likely that node b is unable to make a connection to node a.

# Checking addresses

In the case where node b simply cannot form a connection to node a, despite knowing that it needs to, the likely culprit is a bad NAT. When node b learns that it needs to connect to node a, it checks the DHT for addresses for node a, and then starts trying to connect to them. We can check those addresses by running ipfs dht findpeer <node a peerID> on node b. This command should return a list of addresses for node a. If it doesn't return any addresses, then you should try running the manual providing command from the previous steps. Example output of addresses might look something like this:

/ip4/127.0.0.1/tcp/4001
/ip4/127.0.0.1/udp/4001/quic
/ip4/192.168.2.133/tcp/4001
/ip4/192.168.2.133/udp/4001/quic
/ip4/88.157.217.196/tcp/63674
/ip4/88.157.217.196/udp/63674/quic

In this case, we can see a localhost (127.0.0.1) address, a LAN address (the 192.168.. one), and another address. If this third address matches your external IP, then the network knows a valid external address for your node. At this point, it's safe to assume that your node has a difficult to traverse NAT situation. If this is the case, you can try to enable UPnP or NAT-PMP on the router of node a and retry the process. Otherwise, you can try manually connecting node a to node b.

# Manually connecting node a to node b

On node b run ipfs id and take one of the multiaddrs that contains its public IP address, and then on node a run ipfs swarm connect <multiaddr>. You can also try using a relayed connection. If that still doesn't work, then you should either join IRC and ask for help there or file an issue on GitHub.

If this manual step did work, then you likely have an issue with NAT traversal, and IPFS cannot figure out how to make it through. Please report situations like this to us so we can work on fixing them.

# Go debugging

When you see ipfs doing something (using lots of CPU, memory, or otherwise being weird), the first thing you want to do is gather all the relevant profiling information.

There's a command (ipfs diag profile) that will do this for you and bundle the results up into a zip file, ready to be attached to a bug report.

If you feel intrepid, you can dump this information and investigate it yourself:

  1. goroutine dump:

    curl localhost:5001/debug/pprof/goroutine\?debug=2 > ipfs.stacks`
    
  2. 30-second cpu profile:

    curl localhost:5001/debug/pprof/profile > ipfs.cpuprof`
    
  3. heap trace dump:

    curl localhost:5001/debug/pprof/heap > ipfs.heap
    
  4. memory statistics. In JSON see memstats object:

    curl localhost:5001/debug/vars > ipfs.vars
    
  5. System information:

    ipfs diag sys > ipfs.sysinfo`
    

# Analyzing the stack dump

The first thing to look for is hung goroutines - any goroutine that's been stuck for over a minute will note that in the trace. It looks something like:

goroutine 2306090 [semacquire, 458 minutes]:
sync.runtime_Semacquire(0xc8222fd3e4)
    /home/whyrusleeping/go/src/runtime/sema.go:47 +0x26
sync.(*Mutex).Lock(0xc8222fd3e0)
    /home/whyrusleeping/go/src/sync/mutex.go:83 +0x1c4
gx/ipfs/QmedFDs1WHcv3bcknfo64dw4mT1112yptW1H65Y2Wc7KTV/yamux.(*Session).Close(0xc8222fd340, 0x0, 0x0)
    /home/whyrusleeping/gopkg/src/gx/ipfs/QmedFDs1WHcv3bcknfo64dw4mT1112yptW1H65Y2Wc7KTV/yamux/session.go:205 +0x55
gx/ipfs/QmWSJzRkCMJFHYUQZxKwPX8WA7XipaPtfiwMPARP51ymfn/go-stream-muxer/yamux.(*conn).Close(0xc8222fd340, 0x0, 0x0)
    /home/whyrusleeping/gopkg/src/gx/ipfs/QmWSJzRkCMJFHYUQZxKwPX8WA7XipaPtfiwMPARP51ymfn/go-stream-muxer/yamux/yamux.go:39 +0x2d
gx/ipfs/QmZK81vcgMhpb2t7GNbozk7qzt6Rj4zFqitpvsWT9mduW8/go-peerstream.(*Conn).Close(0xc8257a2000, 0x0, 0x0)
    /home/whyrusleeping/gopkg/src/gx/ipfs/QmZK81vcgMhpb2t7GNbozk7qzt6Rj4zFqitpvsWT9mduW8/go-peerstream/conn.go:156 +0x1f2
    created by gx/ipfs/QmZK81vcgMhpb2t7GNbozk7qzt6Rj4zFqitpvsWT9mduW8/go-peerstream.(*Conn).GoClose
    /home/whyrusleeping/gopkg/src/gx/ipfs/QmZK81vcgMhpb2t7GNbozk7qzt6Rj4zFqitpvsWT9mduW8/go-peerstream/conn.go:131 +0xab

At the top, you can see that this goroutine (number 2306090) has been waiting to acquire a semaphore for 458 minutes. That seems bad. Looking at the rest of the trace, we see the exact line it's waiting on is line 47 of runtime/sema.go. That's not particularly helpful, so we move on. Next, we see that call was made by line 205 of yamux/session.go in the Close method of yamux.Session. This one appears to be the issue.

Given that information, look for another goroutine that might be holding the semaphore in question in the rest of the stack dump.

There are a few different reasons that goroutines can be hung:

  • semacquire means we're waiting to take a lock or semaphore.
  • select means that the goroutine is hanging in a select statement, and none of the cases are yielding anything.
  • chan receive and chan send are waiting for a channel to be received from or sent on, respectively.
  • IO wait generally means that we are waiting on a socket to read or write data, although it can mean we are waiting on a very slow filesystem.

If you see any of those tags without a , X minutes suffix, that generally means there isn't a problem -- you just caught that goroutine in the middle of a short wait for something. If the wait time is over a few minutes, that either means that goroutine doesn't do much, or something is pretty wrong.

If you see a lot of goroutines, consider using stackparse (opens new window) to filter, sort, and summarize them.

# Analyzing the CPU Profile

The go team wrote an excellent article on profiling go programs (opens new window). If you've already gathered the above information, you can skip down to where they start talking about go tool pprof. My go-to method of analyzing these is to run the web command, which generates an SVG dotgraph and opens it in your browser. This is the quickest way to easily point out where the hot spots in the code are.

# Analyzing vars and memory statistics

The output is JSON formatted and includes badger store statistics, the command line run, and the output from Go's runtime.ReadMemStats (opens new window). The MemStats (opens new window) has useful information about memory allocation and garbage collection.